[OpenWrt Wiki] TP-Link Archer C5 AC1200 / TP-Link Archer C7 AC1750 (2024)

Dual Band (concurrent) and Gigabit Ethernet. Advertised as 1750 Mbps. It has simultaneous Triple-Stream (3×3) radios on both 2.4GHz and 5 GHz Bands. It supports 802.11n in 2.4GHz for 450Mbps throughput and IEEE 802.11ac (draft) for 1300Mbps throughput in 5GHz. Note: The editing history for this page is at Previous Archer C5/C7/WDR7500 page

The Archer C5 v1.x: available worldwide, has 3 internal (2.4GHz) and 3 external (5GHz) antennas.

The Archer C5 v2.0: available worldwide, has ?? internal (2.4GHz) and 2 external (5GHz) antennas.

The Archer C7: available worldwide, has 3 internal (2.4GHz) and 3 external (5GHz) antennas.

The Archer C7R (also called the TL-WDR7500): currently available in PRC only, has 6 external antennas.

WARNING: DO NOT install OpenWrt 17.03 or 18.06 on Archer C7 v1.x (and WDR7500 v2.x), the AR1A (v1) variant of QCA9880 wifi card causes a bootloop as the ath10k driver crashes hard when trying to initialize wifi hardware. Also, in older OpenWrt releases the 5GHz 802.11a/n/ac wifi does not work (due to issues with the same wifi card).

Please be aware that OpenWrt firmware does not support the hardware NAT capability of these routers. Hence, the throughput between WAN↔LAN will be slower than with stock firmware. This is only important for users with highspeed internet connections, e.g. a 1G fibre connection. If your internet connection is ⇐200-300 Mbps you don't need to worry about this. But if you need faster NAT throughput, consider buying faster hardware.

More recent testing on OpenWrt 19.07.7 suggests that the venerable Archer C7 (and other single-core, MIPS-based routers with ~720 MHz clock rates) are, under ideal conditions with no wireless or “unnecessary” services running, limited to about the following throughput:

Enabling wireless, running additional applications, or even imperfect ISP lines can significantly limit “real world” performance to well below these values.

SQM is commonly known as “bufferbloat management” or “QoS” and is often very valuable on consumer lines.

→ Install OpenWrt (generic explanation)

Note: The Archer C7 V2.0's web interface does not accept the image .bin file unless you rename it to something with less dots; like openwrt.bin.

• Download the correct version for your router from the tables below.

  • Note that if your router says US, EU, or IL on the sticker on the bottom, you might need a different image than the image linked in the tables below. The images in the table below are for “rest of world” routers. If you browse to the parent directory of the linked images, you'll see the appropriate US, EU, or IL .bin file.

• connect your PC to a LAN port of the TP-link. If the default configuration was not changed, the DHCP on the router will give you a 192.168.0.X address and the TP-link web administration page is http://192.168.0.1/. (User: admin, Password: admin) Under 'System Tools' select 'Firmware Upgrade'. Browse to the previously downloaded *.bin file. Click Upgrade.

  • If the Webinterface tells you 'You have no authority to access this router!' that's because your browser does not send the correct HTTP referer header. Disable addons or use a different browser.

  • If the web interface tells you 'Please choose a file to upgrade', just rename the file to something shorter like openwrt.bin.

• Connect to http://192.168.1.1 with your web browser

• Set your password and configure the router through the web UI. Basic Config

• Congratulations! You just installed OpenWrt on your Router!

Note: Factory default IP address range is 192.168.0.1 while OpenWrt uses 192.168.1.1 by default. If you have trouble accessing your router after initial flash, check that you have a 192.168.1.x IP address on your PC.

Please add the installation procedure here.

Last known good firmware images are Chaos Calmer 15.05.1.

(Updated and tested on March 2017 by orenr)

TP-Link are checking for the file signature in order to verify it. Once trying to flash OpenWrt you will encounter the following error:

Error code: 18005 Upgrade unsuccessfully because the version of the upgraded file was incorrect. Please check the file name.

For TP-Link Archer C7 v2.0, it is enough just to rename the factory image to something like factory.bin, then just upload it via the OEM web interface like a firmware upgrade. Note that if your router says US, EU, or IL on the sticker on the bottom, you might need a different image than the image linked in the tables above. The images in the table above are for “rest of world” routers. If you browse to the parent directory of the linked images, you'll see the appropriate US, EU, or IL .bin file. (tested by tp-linked on May 2018)

For TP-Link Archer C7 v2.1 it is enough just to rename the factory image to something like factory.bin, then just upload it like a firmware upgrade.

Use the following workaround (based on https://www.gargoyle-router.com/phpbb/viewtopic.php?f=8&t=8210)

(Based on http://www.dd-wrt.com/phpBB2/viewtopic.php?p=998919&sid=9bd1c67b9e96384f914718a843aa2ea4)

The most recent version is available in the DDWRT download section: http://dd-wrt.com/site/support/other-downloadsbetas → 2017 → most recent version like “09-27-2017-r33413” → tplink_archer-c7-v2. In this directory, select the factory-to-ddwrt appropriate for your country. There are three different versions - US version, General international and an Israeli version. Download the version suitable for your device.Flash the DD-WRT firmware. Please note that TP-Link defaults to 192.168.0.1, but DD-WRT defaults to 192.168.1.1, so make sure to reconnect the Ethernet cable if your DHCP client cannot figure it out.

Now you need to flash an older version of the vendor firmware, which doesn't check the file signatures.

• Download ArcherC7v2_webrevert.rar from http://everbest.ftpserver.biz/TP-Link/DD-WRT_Revert%20Files/

• Unpack the file using unrar.

• Flash ArcherC7v2_webrevert.bin using DD-WRT web interface.

The router is back on 192.168.0.1 now.

(Updated and tested install on February 2020 by zenith828)

I followed the instructions for installing Archer C7 V4 (see below) successfully.

I started with the most recent FW on the Archer C7 V3 SW version 3.14.3 (release date 2015-05-08)I upgraded to OpenWrt v19.07.1, but I used the binary named the Archer C7 v2, because that's what listed as the binary for the v3. This causes the Model to be listed as “TP-Link Archer C7 v2” on the status page. Hopefully this is the only issue.

I have not done extensive testing on it to ensure that all the functionality is working properly, but I have tested the wireless and everything seems to be in order.

(Updated and tested install on June 2018 + upgrade 2019 by arberg)

• Download current release (see table above or firmware downloads here)

• Rename to for instance firmware.bin

• Install OpenWrt by choosing Upgrade via Router Stock WebUi

I used newest TP-Link firmware when I did the update, in other words I had let TP Link update its original firmware first. This is probably not necessary. The 8 MB Archer C7 v2 file will not install on the C7 v4.

• OpenWrt Upgrade

• Luci > System > Backup/flash firmware > Flash new firmware image

• Choose sysupgrade image, and choose the `openwrt-<version>-ar71xx-generic-archer-c7-v4-squashfs-sysupgrade.bin` file

(Updated and tested on February 2019 by casta)

• Download current release (see table above)

• Rename to for instance firmware.bin

• Upgrade via Router webui

I used an European original firmware (out of the box) when I did the update. WebUI install is working nicely.

(Updated and tested on November 2018 by mac_low)

• Download current release (see table above)

• Rename to for instance ArcherC7v5_tp_recovery.bin

• Set TFTP server under IP:192.168.0.66 with this ArcherC7v5_tp_recovery.bin on the root

• Turn off the router

• Press and hold Reset button

• Turn on router with the reset button pressed and wait 5-10 seconds

• Release the reset button and after a short time the firmware should be transferred from the tftp server

• Wait ~30 second to complete recovery

I used European TP-Link original firmware when I did the update.Also look at this link for Archer c7 v5 (EU) if you have trouble TFTP-ing.

1. Download the corresponding OpenWrt Install (factory, not sysupgrade) image for your router, and rename it to something short like “firmware.bin”

2. Set your computer to the static IP address: 192.168.1.100

3. Start a TFTP server on your computer, and place firmware.bin in the root folder

4. Connect over TTL (speed=115200), and when you see the text “Autobooting in 1 seconds”, quickly type “tpl” to halt the boot process

• You will now be greeted with a command prompt. Firstly we download the firmware over TFTP by issuing the following command:

tftpboot 0x80020000 firmware.bin

• If everything goes well, you will see a message saying “Bytes transferred = 8126464 (7c0000 hex)”. Next we erase the flash. Please take care so that the power will not go out etc. You have been warned!

erase 0x9f020000 +0x7c0000

• If everything goes well, you will see a message saying “Erased 124 sectors”. Finally we write the firmware to flash, by issuing the following command

cp.b 0x80020000 0x9f020000 0x7c0000

• Wait a few minutes after the writing has finished, and power cycle the router. OpenWRT should now start up. Tested by Mats, 2021-01-17

When OpenWrt Designated Driver 50104 was installed, for example, no 5GHz network controller was detected (/etc/config/wireless did not contain the 5GHz radio controller).

To fix, install proper kernel module and firmware packages for your 5GHz WLAN hardware (see tech specs of your Archer model), e.g. for C5 v1 and some C7 versions you would use:

opkg updateopkg install kmod-ath10kopkg install ath10k-firmware-qca988xrm /etc/config/wireless && wifi detect > /etc/config/wirelesscat /etc/config/wirelessreboot

On release 18.xx and later, wifi detect has been deprecated. Use wifi config instead - it will generate /etc/config/wireless for you.

Review Kernel log with dmesg. There can still be warnings like Direct firmware load for ath10k....bin failed, just make sure the device is properly detected in the end. Some firmwares reject to load unless you configure the wifi device country code to the value they suggest in the log (e.g. set option country 'US' in /etc/config/wireless).

Reference - Archer C7 missing ath10 firmware

To enter Failsafe-Mode press the WPS/Reset Button rapidly after starting the router. Stop when the second LED (from left) starts flashing very rapidly. Continue here and here when already logged in in failsafe mode.

If your timing is good, you can save your finger. On power-up, an Archer C7 v2 will do a “light test” and shortly thereafter the power (“sun”) light will go off. It will then start flashing several times per second, for a period of a couple seconds. If you're running a recent build of OpenWrt (tested in March 2018), during that window indicated by fast-flashing, a single click of the WPS/Reset button will get you into failsafe mode. Success in entering failsafe mode is indicated by the power light flashing even faster. If the power light goes to a slower flashing rate or steady on, the window to enter failsafe mode has closed.

If you have accidentally flashed your V1 or V1.1 before realizing that the 5GHz network card will not be supported, and want to return it to factory firmware, you can follow the following instructions (tested on V1.1, harvested from other tp-link device wikis)

The following instruction also works on V2

→ generic.uninstall

Obtain the factory firmware from the OEM:http://www.tplink.com/en/support/download/?model=Archer+C7

• (tested on archer c5 v2) in case the file name of this firmware file does not contain the word “boot” in it, you can simply revert back to original firmware

• in case the file name of this firmware file does contain the word “boot” in it, you need to cut off parts of the image file before flashing it:

An example of an image file with the word “boot” in it is ArcherC7v1_en_3_13_33_up_boot(130729).bin.

Cut the first 0x20200 (that is 131,584 = 257*512) Bytes from original firmware (1*512 Vendor-info + 256*512 U-Boot):

dd if=orig.bin of=tplink.bin skip=257 bs=512

You should transfer the firmeware image to the /tmp folder and revert back to original firmware (if available you can flash the firmware via the webinterface as well):

Via the safer method using sysupgrade:

sysupgrade /tmp/tplink.bin

Or alternatively you can use the mtd method:

mtd -r write /tmp/tplink.bin firmware

The serial-less TFTP recovery method for the TP-Link TL-WDR4300 also works for the Archer C7 (confirmed on v1.1 and v2) and the Archer C5 (v1.20).

For firmware revisions before 3.14.1 (140929), the router looks for an IP address of 192.168.1.66 and a file named ArcherC7v2_tp_recovery.bin. Firmware 3.14.1 updates the bootloader to look for an IP address of 192.168.0.66 and a file named ArcherC7v3_tp_recovery.bin even on hardware v2 units, but may also load ArcherC7v2_tp_recovery.bin. Some v1.1 units may also look for ArcherC7v1_tp_recovery.bin. The model Archer C5 looks for the file ArcherC5v1_tp_recovery.bin.

Setup your computer to 192.168.0.66 or 192.168.1.66 as appropriate for your version (SubnetMask /24 = 255.255.255.0) and connect it to LAN1. Start TFTP server (e.g. tftpd-hpa on debian) and provide recovery file with it. An Archer C7 will repeatedly try at 5-second intervals to connect to the TFTP server if you have the “wrong” address.

To activate TFTP Recovery press and hold WPS/Reset Button during powering on until WPS LED turns on.

For de-bricking with an OpenWrt image use the factory.bin image. In case you are flashing back original firmware, make sure original firmware image name does not contain word boot → return_to_factory_firmware.

Note: the TFTP flashing process requires that the product hardware id and version in the new image header match those in the existing image in flash, otherwise the new image is rejected, flashing is cancelled and the bootloader proceeds to boot the old image. When this happens, the following output is seen on the serial console:

 original_product_id = ffffffff original_product_ver = ffffffff recovery_product_id = c7000002 recovery_product_ver = 01 auto update firmware: product id verify fail!Autobooting in 1 seconds

or

Bytes transferred = 16384512 (fa0200 hex) original_product_id = 00000000 original_product_ver = 00 original_resvered_id = 00 original_special_id = 55530000 recovery_product_id = c7000002 recovery_product_ver = 01 recovery_resvered_id = 01 recovery_support_list = 00000000;55530000; compare special,ret:0 auto update firmware: product id verify fail!

While this would be a fine safety feature in another context, it means the recovery process can reject a valid new image if the image in flash is corrupted. Unfortunately, such corruption can easily occur if the flashing process is interrupted: when an image is accepted, the flashing process first erases the whole space, which takes a while, and then writes the new image. If this process is interrupted during the erasure phase, the in flash header will appear as all 0xFF, and further recovery attempts will therefore fail because the header hardware id and version values will no longer match. If this happens, you'll need to try either a serial connection, or building an image with the header values overridden (in tp-link.mk set TPLINK_HWREV and TPLINK_HWID to 0xffffffff), or override the values corresponding to original_product_id,original_product_ver,original_resvered_id in the firmware image, which start at offset 0x40 in the firmware and stored as 4 byte int each (i.e. set 3*4=12 bytes to 0xFF starting at offset 0x40, if that does not work try setting to 0x00).

Update for debricking without serial on OpenWrt 19.07: After building your own image with the modified TPLINK_HWREV and TPLINK_HWID (you can also download mine here: https://github.com/danielschmalhofer/Important-Openwrt-Things/blob/master/archer_c7_ac1750_debricking.zip) you can flash with tftp the right image. You will see, if you hit the right one, when the blinking takes longer than normal. After that you will be able to access the router via terminal on root@192.168.1.1 - but take care, because for me the image was gone after a reboot. You will have to make a sysupgrade. But the sysupgrade via terminal will fail, because of the corrupting header-infos, and even -F will not help you. So install luci (opkg update && opkg install luci), login via http://192.168.1.1 and upgrade the system via the web interface - there the Force option works.

Connect to your router via serial (TX, RX and GND .. VCC not needed), power it up, then type “tpl” until the boot process is halted and you should be at the console. (Each “tpl” you type must be followed by carriage-return/linefeed. If you're running C-Kermit in an Emacs shell buffer under Linux, the carriage-return character is a control-M.)

If you're having problems getting 'tpl' to work, you may need a pull-up resistor inline on the TX side of the connection, see link. The TX pullup is most likely needed in version 2 models of revision B (serial beginning with 215B...), 16MB flash memory. A pull-up resistor also resolved “bleed through” of binary data into the console on an Archer C7 with a serial number beginning with 2154.

If you find three 220 Ohms resistors and one 150 Ohms resistor in your drawer they will do the trick when put in series. Additionally, if you are puzzled after reading the linked forum post above, this circuit may help (Vcc of the sketched FTDI was set to 3.3V):

 R (~800 Ohms) ------------- /---\/\/\/`------ VCC --RED--| USB FTDI | ----------- | | 3.3V | |Archer V2|-- RX --+----------------- TX --ORA--| | --> to PC (minicom, screen, C-Kermit, ...) |serial |-- TX -------------------- RX --YLW--| | | |-- GND ------------------ GND --BLK--| | ----------- -------------

NOTE: If you are using a 3 pin cable containing an FTDI chip (such as the 3.5mm audio jack version), it is not possible to connect the resistor to VCC on the FTDI side. Instead, use the VCC on the Archer side, this is the normally unused pin next to GND on the 4 pin connection.

Set up a TFTP server with your firmware at 192.168.1.100, then run the following commands:

For 8MB Flash (UNCONFIRMED):

tftp 0x81000000 [name of your firmware file].binerase 0x9f020000 +7c0000cp.b 0x81000000 0x9f020000 0x7c0000reset

For 16MB Flash:

tftp 0x81000000 [name of your firmware file].binerase 0x9f020000 +f80000cp.b 0x81000000 0x9f020000 0xf80000reset

Information about WDR-7500 Ver 6.0.China

PCBhttp://oi66.tinypic.com/2uzsegy.jpg

QCA9563-AL3A MIPS CPUhttp://i66.tinypic.com/o70ft1.jpg

QCA9880-BR4Ahttp://i65.tinypic.com/awt8hx.jpg

RTL8367S Gigabit Switchhttp://i67.tinypic.com/21eb5w6.jpg

One memory chip WinBondW9751G6KB-25 RAMhttp://i63.tinypic.com/wvqszb.jpg

Flash Chip25Q64CSIG (BH1621)http://i65.tinypic.com/9asmqh.jpg

UART J1http://i67.tinypic.com/s1tjlk.jpg

Here is Forum topic about it - https://forum.openwrt.org/viewtopic.php?pid=336271#p336271

I need to remove the Flashchip from the mainboard to connect it to a spi-programmer. I used flashrom (https://flashrom.org) to read out the flash chip. Dont forget to connect the /WP and /RESET Pin to VCC!
flashrom -p ft2232_spi:type=openmoko,divisor=2 -r flash-chip-backup.img
Read it two times with different divisors. Then compare both files with diff. The newest Version of flashrom supports both 16M flash chips.

Is some one have a solution to read it in place over jtag? The VCC connection seem to be direct to the power supply. The programmer need to powers all 3.3V components. But then the cpu could start working...

The included power supply is rated at 2.5A at 12V (30W), but the router does not draw anywhere near the 30 Watts deliverable by that supply. The extra capacity is useful for powering USB devices, however. The following are power measurements taken of an Archer C7 AC1750 V2.0 measuring current over the DC wires. The AC/DC adapter outputs 12.2V loaded. A Kill-A-Watt power meter was used to confirm the measurements and showed the AC/DC adapter was fairly efficient.

• Stock firmware measurements

  • booting draws between 2.4 and 3.5 W

  • idle power 2.4 W

  • downloading file over 2.4 GHz 3.6 W

  • downloading over both 2.4 and 5 GHz 4.1 W

  • flashing firmware 4.4 W

• OpenWrt firmware

  • idle power 2.2 to 2.4 W

  • downloading via wifi at 12 Mbps through router instance of OpenVPN w/compression 3.1 W

  • idle with all gigabit ports connected and both wlans enabled: 5.5 W

Archer C7 USB benchmark results

Using a Lexar L19 USB3.0 Stick (rated >40MB/s read/write). Encrypted transfers reduce performance heavily.

• EXT2 USB → Router → SFTP → PC : 2.6MB/s

• EXT2 USB → Router → SCP → PC : 3.6MB/s

• EXT2 USB → Router → FTP (unencrypted) → PC : 14.9-15.5MB/s

• Router /dev/zero → EXT2 USB : 10-19,42MB/s (depending on BS parameter of dd)

• switch port map

Switch Ports:

Note: It seems that Archer C5 has a slightly different structure. Switch has 6 ports and the only interface eth0 connects to it carrying both VLAN1 and VLAN2. See page TP-Link Archer C5 v4. v2 is similar. So the overall full duplex WAN throughput cannot exceed 1 Gbps.

: Information on the pinout of JP4 would be helpful

Configure your favorite terminal with the following settings: 115200 baud, 8 bit, no parity, 1 stop bit, no flow control.

Warning!
The labels in the image look wrong (confirmed with real hardware). It should be VCC, GND, RX, TX. The second pin has four connections to the surrounding mass, so is GND. The first pin has a capacitor, which points to the fact that it is VCC.

You can use an inexpensive PL2303 USB to UART adapter to connect to this router.

Note: The adapter linked is not officially compatible with Windows 8 and above. You will need an older driver (1.5) for it to work with newer versions of Windows. Be sure to disable automatic driver updates, or else Windows will use the newer, incompatible driver.

It is recommended that you solder a serial header for the most reliable connection, but in case you don't want to solder or you're just trying to quickly unbrick your router without making it obvious that you voided your warranty, male-to-male jumper wires will work.

Configure your favorite terminal with the following settings: 115200 baud, 8 bit, no parity, 1 stop bit, no flow control.

I don't know what to really call this. I've been told on IRC that it is more like the WDR-7500. See the label pic and decide for yourself:

Here is a full board pic:

And zoomed in on the chips so they're readable:

In the lower right is the serial header. The first through hole is TX, second RX and third GROUND. There were two missing resistors at R27 and R24. I placed a 10K on R27 and a 1K on R24 (total shot in the dark based on some reading I had done, but it works). The RX through hole didn't seem to be connected to the right side of the R24 pad so it's got a solder bridge. Use 115200, 8N1, no flow control.

(FYI: from TP-Link engineering, R24 = 220R, R27 = 1K)

As I didn't have 0402 sized resistors at home, I've used just one 0603 of 180R value.

U-Boot 1.1.4 (Jan 26 2013 - 13:35:40)ap135 - Scorpion 1.0DRAM: sriScorpion 1.0ath_ddr_initial_config(178): (32bit) ddr2 inittap = 0x00000003Tap (low, high) = (0x3, 0x1f)Tap values = (0x11, 0x11, 0x11, 0x11)128 MBFlash Manuf Id 0x1c, DeviceId0 0x30, DeviceId1 0x17flash size 8MB, sector count = 128Flash: 8 MBUsing default environment*** Warning *** : PCIe WLAN Module not found !!!In: serialOut: serialErr: serialNet: ath_gmac_enet_initialize...athrs_sgmii_res_cal: cal value = 0xeNo valid address in Flash. Using fixed addressNo valid address in Flash. Using fixed addressath_gmac_enet_initialize: reset mask:c02200 Scorpion ----> S17 PHY *Vlan config...TEST: FINAL REG VAL after TX Calibration - 0x46000000TEST: FINAL XMII VAL after RX Calibration - 0x56000000TEST: FINAL ETH_CFG VAL after RX Calibration - 0x00028001athrs17_reg_init: complete: cfg1 0x80000000 cfg2 0x7335eth0: ba:be:fa:ce:08:41eth0 upathrs17_reg_init_wan doneSGMII in forced modeathr_gmac_sgmii_setup SGMII done: cfg1 0x800c0000 cfg2 0x7214eth1: ba:be:fa:ce:08:41eth1 upeth0, eth1Setting 0x18116290 to 0x54a9214fAutobooting in 1 seconds## Booting image at 9f020000 ... Uncompressing Kernel Image ... OKStarting kernel ...Booting QCA955x\00Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #1 Sat Jan 26 13:40:17 CST 2013Ram size passed from bootloader =128Mflash_size passed from bootloader = 8CPU revision is: 00019750 (MIPS 74Kc)cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 600 ahb 200Determined physical RAM map: memory: 08000000 @ 00000000 (usable)Zone PFN ranges: Normal 0x00000000 -> 0x00008000Movable zone start PFN for each nodeearly_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00008000Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6912k(rootfs),64k(config),64k(ART) mem=128MPID hash table entries: 512 (order: 9, 2048 bytes)Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytesWriting ErrCtl register=00000000Readback ErrCtl register=00000000Memory: 112868k/131072k available (1889k kernel code, 18028k reserved, 435k data, 120k init, 0k highmem)NR_IRQS:128plat_time_init: plat time init doneCalibrating delay loop... 359.42 BogoMIPS (lpj=718848)Mount-cache hash table entries: 512****************ALLOC*********************** Packet mem: 802774e0 (0xe00000 bytes)********************************************NET: Registered protocol family 16ath_pcibios_init: bus 0***** Warning PCIe 0 H/W not found !!!registering PCI controller with io_map_base unsetath_pcibios_init: bus 1ath_pcibios_init(232): PCI 1 CMD write: 0x356registering PCI controller with io_map_base unsetReset button pressed.bio: create slab <bio-0> at 0pcibios_map_irq: IRQ 76 for bus 1NET: Registered protocol family 2IP route cache hash table entries: 1024 (order: 0, 4096 bytes)TCP established hash table entries: 4096 (order: 3, 32768 bytes)TCP bind hash table entries: 4096 (order: 2, 16384 bytes)TCP: Hash tables configured (established 4096 bind 4096)TCP reno registeredNET: Registered protocol family 1ATH GPIOC major 0squashfs: version 4.0 (2009/01/31) Phillip Loughermsgmni has been set to 220Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)io scheduler noop registeredio scheduler deadline registered (default)Serial: 8250/16550 driver, 1 ports, IRQ sharing disabledserial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550Aconsole [ttyS0] enabledPPP generic driver version 2.4.2NET: Registered protocol family 245 cmdlinepart partitions found on MTD device ath-nor0Creating 5 MTD partitions on "ath-nor0":0x000000000000-0x000000020000 : "u-boot"0x000000020000-0x000000120000 : "kernel"0x000000120000-0x0000007e0000 : "rootfs"0x0000007e0000-0x0000007f0000 : "config"0x0000007f0000-0x000000800000 : "ART"->Oops: flash id 0x1c3017 . TCP cubic registeredNET: Registered protocol family 10NET: Registered protocol family 17802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>All bugs added by David S. Miller <davem@redhat.com>athwdt_init: Registering WDT successath_otp_init: Registering OTP successVFS: Mounted root (squashfs filesystem) readonly on device 31:2.Freeing unused kernel memory: 120k freedinit started: BusyBox v1.01 (2012.11.27-00:48+0000) multi-call binaryThis Board use 2.6.31xt_time: kernel timezone is -0000nf_conntrack version 0.5.0 (2048 buckets, 8192 max)CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please usenf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option orsysctl net.netfilter.nf_conntrack_acct=1 to enable it.ip_tables: (C) 2000-2006 Netfilter Core Teaminsmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directoryinsmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directoryPPPoL2TP kernel driver, V1.0PPTP driver version 0.8.3insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory (none) mips #1 Sat Jan 26 13:40:17 CST 2013 (none)(none) login: qca955x_GMAC: Length per segment 1536955x_GMAC: qca955x_gmac_attach955x_GMAC: qca955x_set_gmac_capsCurrently in polling mode unit1mac:1 Registering S17....qca955x_GMAC: RX TASKLET - Pkts per Intr:200qca955x_GMAC: Max segments per packet : 1qca955x_GMAC: Max tx descriptor count : 220qca955x_GMAC: Max rx descriptor count : 220qca955x_GMAC: Mac capability flags : 12002200955x_GMAC: qca955x_gmac_attach955x_GMAC: qca955x_set_gmac_capsCurrently in polling mode unit0mac:0 Registering S17....qca955x_GMAC: RX TASKLET - Pkts per Intr:200qca955x_GMAC: Max segments per packet : 1qca955x_GMAC: Max tx descriptor count : 220qca955x_GMAC: Max rx descriptor count : 220qca955x_GMAC: Mac capability flags : 10002A00955x_GMAC: Serdes PLL is locked value 0x1f038116athr_gmac_ring_alloc Allocated 3520 at 0x87950000athr_gmac_ring_alloc Allocated 3520 at 0x87a8e000955x_GMAC: eth1 in SGMII MODEScorpion -----> S17 PHYACL is not yet enabled. Enabling... Hello, nat helper module for 1.08!netlink_kernel_create succeeded at tp_rule_nl_prot: [29]######## S17 SSDK init succeeded! ########_athrs17_mac0_intf SGMII doneathrs17_reg_init:done955x_SGMII::athr_gmac_sgmii_setup DoneSetting Drop CRC Errors, Pause Frames and Length Error frames Setting PHY...Phy setup CompleteADDRCONF(NETDEV_UP): eth0: link is not readydevice eth0.1 entered promiscuous modedevice eth0 entered promiscuous modeSET INTF MAC 0:1c-fa-68-fe-32-f4SET INTF MAC 1:1c-fa-68-fe-32-f5br0: port 1(eth0.1) entering forwarding statenf_conntrack_rtsp v0.6.21 loadingnf_nat_rtsp v0.6.21 loadingadf: module license 'Proprietary' taints kernel.Disabling lock debugging due to kernel taintath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reservedath_dfs: Version 2.0.0Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reservedath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reservedath_ahb: 10.0.107 (Atheros/multi-bss)check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.Enterprise mode: 0x43fc0000Restoring Cal data from Flashcheck DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.ath_get_caps[5863] rx chainmask mismatch actual 7 sc_chainmak 0ath_get_caps[5838] tx chainmask mismatch actual 7 sc_chainmak 0check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.SC Callback Registration for wifi0wifi0: Atheros ???: mem=0xb8100000, irq=2ath_pci: 10.0.107 (Atheros/multi-bss)ath_pci_probeath_pci 0000:01:00.0: ath DEBUG: sc=0x87aa7ce0 ol_ath_pci_configure : num_desired MSI set to 0 Using PCI Legacy Interrupt__ol_ath_attach: ath_attach TODOol_ath_attach() BMI inited.ol_ath_attach() BMI Get Target Info.ol_ath_attach() TARGET TYPE: 7 Vers 0x4000002cNUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0ol_ath_attach() configure Target .ol_transfer_bin_file: flash cal data len 65535 doesn't equal to 2116ol_transfer_bin_file: Board data file AR9888v1ol_transfer_bin_file 1535: Download Board data len 2116ol_ath_download_firmware: Using 0x1234 for the remainder of initol_transfer_bin_file 1527: Download OTP data len 3572ol_transfer_bin_file 1553: Download Firmware data len 183920ol_ath_attach() Download FW. ol_ath_attach() HT Create .ol_ath_attach() HIF Claim.ol_ath_attach() BMI Done. ol_ath_attach() WMI attached. wmi_handle 86ce0000 +HWT-HWTHTC Service:0x0300 ep:1 TX flow control disabledTXRX: Created pdev 86df3a00wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event num_rf_chain : 00000003ht_cap_info: : 0000085bvht_cap_info : 338001b2vht_supp_mcs : 0000ffeawmi_ready_event_rx: WMI UNIFIED READY event ol_ath_connect_htc() WMI is readyol_ath_set_host_app_area TODOol_ath_attach() connect HTC. target uses HTT version 2.0; host uses 2.0ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080ol_ath_phyerr_attach: calledOL Resmgr Init-edol_if_dfs_setup: calledol_if_dfs_attach: called; ptr=87af3974, radar_info=87addb98ol_ath_rtt_meas_report_attach: calledol_ath_attach() UMAC attach . __ol_ath_attach: init tx/rx TODO__ol_ath_attach: hard_header_len reservation 58__ol_ath_attach: dev name wifi1SC Callback Registration for wifi1check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.VAP device ath0 created DES SSID SET=<redacted> ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.Invoking ACS module for Best channel selection check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.Channel 1 average beacon RSSI 25 noisefloor -107 ieee80211_acs_find_best_11ng_centerchan chan: 1 beacon RSSI + weighted noisefloor: -189Channel 6 average beacon RSSI 8 noisefloor -107 ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -206Channel 6 average beacon RSSI 8 noisefloor -107 ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -206Channel 11 average beacon RSSI 9 noisefloor -107 ieee80211_acs_find_best_11ng_centerchan chan: 11 beacon RSSI + weighted noisefloor: -205ieee80211_acs_find_best_11ng_centerchan found best 11ng center chan: 6 rssi: -206check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.ieee80211_dfs_cac_start[267] ===NON DFS chan === 2437check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.ieee80211_dfs_cac_start[267] ===NON DFS chan === 2437check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.athr_gmac_ring_alloc Allocated 3520 at 0x86dfd000athr_gmac_ring_alloc Allocated 3520 at 0x87ae4000955x_GMAC: eth0 in RGMII MODEScorpion -----> S17 PHYathrs17_reg_init_wan doneSetting Drop CRC Errors, Pause Frames and Length Error frames Setting PHY...ADDRCONF(NETDEV_UP): eth1: link is not readydevice eth1 entered promiscuous modecheck DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.ieee80211_dfs_cac_start[267] ===NON DFS chan === 2437device ath0 entered promiscuous modebr1: port 2(ath0) entering forwarding state ieee80211_ioctl_siwmode: imr.ifm_active=918144, new mode=3, valid=1 check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.br1: port 2(ath0) entering disabled state DEVICE IS DOWN ifname=ath0 DEVICE IS DOWN ifname=ath0check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.ieee80211_dfs_cac_start[267] ===NON DFS chan === 2437br1: port 2(ath0) entering forwarding statecheck DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.br1: port 2(ath0) entering disabled statebr1: starting userspace STP failed, starting kernel STPcheck DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.check DDR Activity - HIGHar9300_set_reset: Scorpion SoC RTC reset done.ieee80211_dfs_cac_start[267] ===NON DFS chan === 2437br1: topology change detected, propagatingbr1: port 2(ath0) entering forwarding stateisCountryCodeValid: EEPROM regdomain 0x52ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080ath_ioctl: SIOC80211IFCREATE CALLEDwmi_unified_vdev_create_send: ID = 0 VAP Addr = 1c:fa:68:fe:32:f2:TXRX: Created vdev 86f6ee00 (1c:fa:68:fe:32:f2)VAP device ath1 created TXRX: ol_txrx_peer_find_add_id: peer 86f60400 ID 129TXRX: ol_txrx_peer_find_add_id: peer 86f60400 ID 145Setting vdev param = f, value = 1ol_ath_vap_set_param: VAP param unsupported param:80 value:1ol_ath_vap_set_param: VAP param unsupported param:35 value:0 DES SSID SET=<redacted> ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 OL vap_stop +wmi_unified_vdev_stop_send OL vap_stop -STOPPED EVENT for vap 0 Setting vdev param = 1a, value = 1Setting vdev param = 3, value = 100Setting vdev param = d, value = 1Setting vdev param = 12, value = 1Setting vdev param = 1e, value = 1OL vap_stop +wmi_unified_vdev_stop_send OL vap_stop -STOPPED EVENT for vap 0 OL vap_start +OL vap_start -ol_vdev_start_resp_evol_ath_vap_join: join operation is only for STA/IBSS modeset channel freq 5745 WMI channel freq=5745, mode=a band_center_freq1=5775ol_if_dfs_configure: calledol_if_dfs_disable: calledol_ath_wmm_update:ieee80211_dfs_cac_start[267] ===NON DFS chan === 5745Setting vdev param = 3, value = 100Notification to UMAC VAP layerFIRMWARE:75 C ,5401 M 1f 5775 2f 9744 408 device ath1 entered promiscuous modebr1: topology change detected, propagatingbr1: port 3(ath1) entering forwarding state ieee80211_ioctl_siwmode: imr.ifm_active=131738, new mode=3, valid=1 wmi_unified_vdev_stop_send STOPPED EVENT for vap 0 br1: port 3(ath1) entering disabled stateol_ath_vap_set_param: VAP param unsupported param:32 value:0ol_ath_vap_set_param: VAP param unsupported param:121 value:1 DEVICE IS DOWN ifname=ath1 DEVICE IS DOWN ifname=ath1ol_ath_vap_set_param: VAP param unsupported param:32 value:0ol_ath_vap_set_param: VAP param unsupported param:32 value:0ol_ath_vap_set_param: VAP param unsupported param:32 value:1ol_ath_vap_set_param: VAP param unsupported param:74 value:1 Group Keyidx set=1 wmi_unified_vdev_install_key_send Setting Key for Macaddress:0xf232fe68fa1c Keyix=1 Keylen=16 Keyflags=1 Cipher=4 Keydata=0x71 0xdd 0x9c 0x85 0x11 0x96 0x2a 0xd5 0x2d 0x82 0xfa 0xac 0x1a 0x96 0xa7 0x3d ol_ath_vap_set_param: VAP param unsupported param:74 value:0TXRX: ol_txrx_peer_find_add_id: peer 86f60400 ID 114TXRX: sec spec for peer 86f60400 (1c:fa:68:fe:32:f2): mcast key of type 6Setting vdev param = 1f, value = 1OL vap_stop +wmi_unified_vdev_stop_send OL vap_stop -STOPPED EVENT for vap 0 OL vap_start +OL vap_start -ol_vdev_start_resp_evol_ath_vap_join: join operation is only for STA/IBSS modeset channel freq 5745 WMI channel freq=5745, mode=a band_center_freq1=5775ol_if_dfs_configure: calledol_if_dfs_disable: calledol_ath_wmm_update:ieee80211_dfs_cac_start[267] ===NON DFS chan === 5745Setting vdev param = 3, value = 100Notification to UMAC VAP layerFIRMWARE:75 C ,5401 M 1f 5775 2f 8624 238 br1: topology change detected, propagatingbr1: port 3(ath1) entering forwarding stateFWLOG: [32170] WAL_DBGID_SECURITY_ENCR_EN ( )FWLOG: [32170] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )wmi_unified_vdev_stop_send STOPPED EVENT for vap 0 br1: port 3(ath1) entering disabled stateOL vap_stop +wmi_unified_vdev_stop_send OL vap_stop -STOPPED EVENT for vap 0 OL vap_start +OL vap_start -ol_vdev_start_resp_evol_ath_vap_join: join operation is only for STA/IBSS modeset channel freq 5745 WMI channel freq=5745, mode=a band_center_freq1=5775ol_if_dfs_configure: calledol_if_dfs_disable: calledol_ath_wmm_update:ieee80211_dfs_cac_start[267] ===NON DFS chan === 5745Setting vdev param = 3, value = 100Notification to UMAC VAP layerFIRMWARE:75 C ,5401 M 1f 5775 2f 8624 238 br1: topology change detected, propagatingbr1: port 3(ath1) entering forwarding statefuse init (API version 7.12)usbcore: registered new interface driver usbfsusbcore: registered new interface driver hubusbcore: registered new device driver usbehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) DriverPort Status 1c000004 ath-ehci ath-ehci.0: ATH EHCIath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1ehci_reset Intialize USB CONTROLLER in host mode: 13ehci_reset Port Status 1c000000 ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000ehci_reset Intialize USB CONTROLLER in host mode: 13ehci_reset Port Status 1c000000 ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00usb usb1: configuration #1 chosen from 1 choicehub 1-0:1.0: USB hub foundhub 1-0:1.0: 1 port detectedPort Status 1c000000 ath-ehci1 ath-ehci1.1: ATH EHCIath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2ehci_reset Intialize USB CONTROLLER in host mode: 13ehci_reset Port Status 1c000000 ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000ehci_reset Intialize USB CONTROLLER in host mode: 13ehci_reset Port Status 1c000000 ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00usb usb2: configuration #1 chosen from 1 choicehub 2-0:1.0: USB hub foundhub 2-0:1.0: 1 port detectedSCSI subsystem initializedInitializing USB Mass Storage driver...usbcore: registered new interface driver usb-storageUSB Mass Storage support registered. GPL NetUSB up!kc 86 : run_telnetDBGDServer start kc 223 : init_DebugD endINFO1758: NetUSB 1.184, 0002061F : May 7 2012 10:35:23INFO175A: AUTH ISOCINFO175B: usbcore: registered new interface driver KC NetUSB General DriverINFO0076: init proc : PAGE_SIZE 4096INFO17B4: Check mac addressINFO162C: infomap 8668c220 INFO162F: sleep to wait br0 to wake upINFO02D0: use dev Name br0 INFO1638: sleep to wait br0 end.INFO1651: UDP_BROAD 7437 tcpPort:625868800 INFO02D0: use dev Name br0 INFO1538: tcpConnector() started...955x_GMAC: qca955x_soc_gmac_set_mac_duplex 955x_GMAC: qca955x_soc_gmac_set_link DoneADDRCONF(NETDEV_CHANGE): eth1: link becomes readybr1: topology change detected, propagatingbr1: port 1(eth1) entering forwarding stateEnet:1 port1 up955x_GMAC: enet unit:1 is up...eth1 SGMII 1000Mbps full duplex955x_GMAC: qca955x_soc_gmac_set_mac_duplex 955x_GMAC: qca955x_soc_gmac_set_link Done955x_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl ADDRCONF(NETDEV_CHANGE): eth0: link becomes readyINFO1415: Bind to br0

U-Boot 1.1.4 (Apr 23 2015 - 13:39:44)ap135 - Scorpion 1.0DRAM:sriScorpion 1.0ath_ddr_initial_config(178): (32bit) ddr2 inittap = 0x00000003Tap (low, high) = (0x2, 0x1b)Tap values = (0xe, 0xe, 0xe, 0xe)128 MBFlash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17flash size 8MB, sector count = 128Flash: 8 MBUsing default environment*** Warning *** : PCIe WLAN Module not found !!!In: serialOut: serialErr: serialNet: ath_gmac_enet_initialize...athrs_sgmii_res_cal: cal value = 0xeNo valid address in Flash. Using fixed addressNo valid address in Flash. Using fixed addressath_gmac_enet_initialize: reset mask:c02200Scorpion ----> S17 PHY *athrs17_reg_init: complete: cfg1 0x80000000 cfg2 0x7114eth0: ba:be:fa:ce:08:41eth0 upathrs17_reg_init_wan doneSGMII in forced modeathr_gmac_sgmii_setup SGMII done: cfg1 0x800c0000 cfg2 0x7214eth1: ba:be:fa:ce:08:41eth1 upeth0, eth1Setting 0x18116290 to 0x50a1214fAutobooting in 1 seconds## Booting image at 9f020000 ... Uncompressing Kernel Image ... OKStarting kernel ...Booting QCA955xLinux version 2.6.31--LSDK-9.2.0_U6.616 (tplink@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #1 Thu Apr 23 13:43:15 CST 2015Ram size passed from bootloader =128Mflash_size passed from bootloader = 8CPU revision is: 00019750 (MIPS 74Kc)cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 600 ahb 200Determined physical RAM map: memory: 08000000 @ 00000000 (usable)Zone PFN ranges: Normal 0x00000000 -> 0x00008000Movable zone start PFN for each nodeearly_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00008000Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6912k(rootfs),64k(config),64k(ART) mem=128MPID hash table entries: 512 (order: 9, 2048 bytes)Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytesWriting ErrCtl register=00000000Readback ErrCtl register=00000000Memory: 112868k/131072k available (1891k kernel code, 18036k reserved, 441k data, 120k init, 0k highmem)NR_IRQS:128plat_time_init: plat time init doneCalibrating delay loop... 359.42 BogoMIPS (lpj=718848)Mount-cache hash table entries: 512****************ALLOC*********************** Packet mem: 802794e0 (0xe00000 bytes)********************************************NET: Registered protocol family 16ath_pcibios_init: bus 0***** Warning PCIe 0 H/W not found !!!registering PCI controller with io_map_base unsetath_pcibios_init: bus 1ath_pcibios_init(232): PCI 1 CMD write: 0x356registering PCI controller with io_map_base unset===@@@@@@@@@@@=>use GPIO13 as wifi button control!bio: create slab <bio-0> at 0pcibios_map_irq: IRQ 76 for bus 1NET: Registered protocol family 2IP route cache hash table entries: 1024 (order: 0, 4096 bytes)TCP established hash table entries: 4096 (order: 3, 32768 bytes)TCP bind hash table entries: 4096 (order: 2, 16384 bytes)TCP: Hash tables configured (established 4096 bind 4096)TCP reno registeredNET: Registered protocol family 1ATH GPIOC major 0squashfs: version 4.0 (2009/01/31) Phillip Loughermsgmni has been set to 220Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)io scheduler noop registeredio scheduler deadline registered (default)Serial: 8250/16550 driver, 1 ports, IRQ sharing disabledserial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550Aconsole [ttyS0] enabledPPP generic driver version 2.4.2NET: Registered protocol family 245 cmdlinepart partitions found on MTD device ath-nor0Creating 5 MTD partitions on "ath-nor0":0x000000000000-0x000000020000 : "u-boot"0x000000020000-0x000000120000 : "kernel"0x000000120000-0x0000007e0000 : "rootfs"0x0000007e0000-0x0000007f0000 : "config"0x0000007f0000-0x000000800000 : "ART"->Oops: flash id 0xef4017 .Ooops, why the devices couldn't been initialed?TCP cubic registeredNET: Registered protocol family 10NET: Registered protocol family 17802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>All bugs added by David S. Miller <davem@redhat.com>athwdt_init: Registering WDT successath_otp_init: Registering OTP successVFS: Mounted root (squashfs filesystem) readonly on device 31:2.Freeing unused kernel memory: 120k freedinit started: BusyBox v1.01 (2015.04.23-05:49+0000) multi-call binaryThis Board use 2.6.31xt_time: kernel timezone is -0000nf_conntrack version 0.5.0 (2048 buckets, 81920 max)CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please usenf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option orsysctl net.netfilter.nf_conntrack_acct=1 to enable it.ip_tables: (C) 2000-2006 Netfilter Core Teaminsmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directoryinsmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directoryPPPoL2TP kernel driver, V1.0PPTP driver version 0.8.3insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory (none) mips #1 Thu Apr 23 13:43:15 CST 2015 (none)(none) login: qca955x_GMAC: Length per segment 1536955x_GMAC: qca955x_gmac_attach955x_GMAC: qca955x_set_gmac_capsCurrently in polling mode unit1mac:1 Registering S17....qca955x_GMAC: RX TASKLET - Pkts per Intr:200qca955x_GMAC: Max segments per packet : 1qca955x_GMAC: Max tx descriptor count : 220qca955x_GMAC: Max rx descriptor count : 220qca955x_GMAC: Mac capability flags : 12002200955x_GMAC: qca955x_gmac_attach955x_GMAC: qca955x_set_gmac_capsCurrently in polling mode unit0mac:0 Registering S17....qca955x_GMAC: RX TASKLET - Pkts per Intr:200qca955x_GMAC: Max segments per packet : 1qca955x_GMAC: Max tx descriptor count : 220qca955x_GMAC: Max rx descriptor count : 220qca955x_GMAC: Mac capability flags : 10002A00955x_GMAC: Serdes PLL is locked value 0x1f038116athr_gmac_ring_alloc Allocated 3520 at 0x87950000athr_gmac_ring_alloc Allocated 3520 at 0x87a99000955x_GMAC: eth1 in SGMII MODEScorpion -----> S17 PHYttl zero adding rule #0ACL is not yet enabled. Enabling...ttl one adding rule #1UDP checksum 0 adding rule #3Hello, nat helper module for 1.08!netlink_kernel_create succeeded at tp_rule_nl_prot: [29]######## S17 SSDK init succeeded! ########_athrs17_mac0_intf SGMII doneathrs17_reg_init:done955x_SGMII::athr_gmac_sgmii_setup DoneSetting Drop CRC Errors, Pause Frames and Length Error framesSetting PHY...Phy setup CompleteADDRCONF(NETDEV_UP): eth0: link is not readydevice eth0.1 entered promiscuous modedevice eth0 entered promiscuous modeSET INTF MAC 0:ec-26-ca-f0-0e-c8SET INTF MAC 1:ec-26-ca-f0-0e-c9br0: port 1(eth0.1) entering forwarding stateAdding ACL rules 2 - wan to lan, dst ip is lan netnf_conntrack_rtsp v0.6.21 loadingnf_nat_rtsp v0.6.21 loadingadf: module license 'Proprietary' taints kernel.Disabling lock debugging due to kernel taintath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reservedath_dfs: Version 2.0.0Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reservedath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reservedath_ahb: 10.1.467 (Atheros/multi-bss)__ath_attach: Set global_scn[0]Enterprise mode: 0x43fc0000Restoring Cal data from FlashGreen-AP : Green-AP : Attachedath_get_caps[5956] rx chainmask mismatch actual 7 sc_chainmak 0ath_get_caps[5931] tx chainmask mismatch actual 7 sc_chainmak 0ath_attach_dfs[11935] dfsdomain 1SC Callback Registration for wifi0wifi0: Atheros ???: mem=0xb8100000, irq=2ath_pci: 10.1.467 (Atheros/multi-bss)ath_pci_probePCI device id is 003c :003cath_pci 0000:01:00.0: ath DEBUG: sc=0x86ebbe00 ol_ath_pci_configure : num_desired MSI set to 0 Using PCI Legacy Interrupt__ol_ath_attach: ath_attach TODOol_ath_attach() BMI inited.ol_ath_attach() BMI Get Target Info.ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016cNUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0ol_ath_attach() configure Target .qc98xx_verify_checksum: flash checksum passed: 0xb25fol_transfer_bin_file 1688: Download Flash data len 2116ol_transfer_bin_file 1635: Download Firmware data len 190448ol_ath_attach() Download FW.ol_ath_attach() HT Create .ol_ath_attach() HIF Claim.ol_ath_attach() BMI Done.ol_ath_attach() WMI attached. wmi_handle 86e30000+HWTCE_recv_buf_enqueue 457 Populate last entry 512 for CE 5CE_recv_buf_enqueue 466 CE 5 wi 511 dest_ptr 0x5eb500 nbytes 0 recv_ctxt 0x86c34800-HWTHTC Service:0x0300 ep:1 TX flow control disabledCE_pkt_dl_len_set CE 4 Pkt download length 42TXRX: Created pdev 86ebb800wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY eventnum_rf_chain : 00000003ht_cap_info: : 0000085bvht_cap_info : 338001b2vht_supp_mcs : 0000ffeaLARGE_AP enabled. num_peers 144, num_vdevs 16, num_tids 256idx 0 req 1 num_units 0 num_unit_info 2 unit size 404 actual units 145chunk 0 len 58580 requested ,ptr 0x6f20000FIRMWARE:P 145 V 16 T 443wmi_ready_event_rx: WMI UNIFIED READY eventol_ath_connect_htc() WMI is readyol_ath_set_host_app_area TODOtarget uses HTT version 2.1; host uses 2.1ol_ath_attach() connect HTC.ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080Skipping VHT80 channel 5825ol_ath_phyerr_attach: calledOL Resmgr Init-edGreen-AP : Green-AP : AttachedGreen-AP : Attachedol_if_dfs_setup: calledol_if_dfs_attach: called; ptr=86f09974, radar_info=87bd7be8ol_ath_rtt_meas_report_attach: calledol_ath_attach() UMAC attach .ol_if_dfs_configure: calledol_if_dfs_configure: FCC domainol_if_dfs_disable: calledol_ath_attach: Calling ol_if_dfs_configure__ol_ath_attach: init tx/rx TODO__ol_ath_attach: hard_header_len reservation 58__ol_ath_attach: dev name wifi1SC Callback Registration for wifi1ath_attach_dfs[11935] dfsdomain 1VAP device ath0 created DES SSID SET=TP-LINK_0EC7 ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1Invoking ACS module for Best channel selectionChannel 1 average beacon RSSI 37 noisefloor -107 ieee80211_acs_find_best_11ng_centerchan chan: 1 beacon RSSI + weighted noisefloor: -177Channel 6 average beacon RSSI 13 noisefloor -106 ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -199Channel 6 average beacon RSSI 13 noisefloor -106 ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -199Channel 11 average beacon RSSI 13 noisefloor -107 ieee80211_acs_find_best_11ng_centerchan chan: 11 beacon RSSI + weighted noisefloor: -201ieee80211_acs_find_best_11ng_centerchan found best 11ng center chan: 11 rssi: -201athr_gmac_ring_alloc Allocated 3520 at 0x86f07000athr_gmac_ring_alloc Allocated 3520 at 0x87a36000955x_GMAC: eth0 in RGMII MODEScorpion -----> S17 PHYathrs17_reg_init_wan doneSetting Drop CRC Errors, Pause Frames and Length Error framesSetting PHY...ADDRCONF(NETDEV_UP): eth1: link is not readydevice eth1 entered promiscuous modedevice ath0 entered promiscuous modebr1: port 2(ath0) entering forwarding state ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, valid=1br1: port 2(ath0) entering disabled state DEVICE IS DOWN ifname=ath0 DEVICE IS DOWN ifname=ath0br1: port 2(ath0) entering forwarding stateEnet:1 port1 up955x_GMAC: enet unit:1 is up...eth1 SGMII 1000Mbps full duplex955x_GMAC: qca955x_soc_gmac_set_mac_duplex955x_GMAC: qca955x_soc_gmac_set_link Done955x_GMAC: done cfg2 0x7215 ifctl 0x0 miictrlADDRCONF(NETDEV_CHANGE): eth0: link becomes ready955x_GMAC: qca955x_soc_gmac_set_mac_duplex955x_GMAC: qca955x_soc_gmac_set_link DoneADDRCONF(NETDEV_CHANGE): eth1: link becomes readybr1: port 1(eth1) entering forwarding stateeth1: received packet with own address as source addressbr1: port 2(ath0) entering disabled statebr1: port 2(ath0) entering forwarding stateisCountryCodeValid: EEPROM regdomain 0x0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080Skipping VHT80 channel 5825ath_ioctl: SIOC80211IFCREATE CALLEDwmi_unified_vdev_create_send: ID = 0 VAP Addr = ec:26:ca:f0:0e:c6:TXRX: Created vdev 86ff1b00 (ec:26:ca:f0:0e:c6)Setting vdev param = 26, value = 147Setting vdev param = 27, value = 295Setting vdev param = 28, value = 300VAP device ath1 createdTXRX: ol_txrx_peer_find_add_id: peer 8660b000 ID 401TXRX: ol_txrx_peer_find_add_id: peer 8660b000 ID 385eth1: received packet with own address as source addressSetting vdev param = f, value = 1ol_ath_vap_set_param: VAP param unsupported param:80 value:1ol_ath_vap_set_param: VAP param unsupported param:35 value:0 DES SSID SET=TP-LINK_5G_0EC6 ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1OL vap_stop +wmi_unified_vdev_stop_sendOL vap_stop -STOPPED EVENT for vap 0Setting vdev param = 2a, value = 2ol_ath_vap_set_param: VAP param is now supported param:62 value:2OL vap_stop +wmi_unified_vdev_stop_sendOL vap_stop -STOPPED EVENT for vap 0OL vap_stop +wmi_unified_vdev_stop_sendOL vap_stop -STOPPED EVENT for vap 0FWLOG: [29837] WHAL_ERROR_RECV_STOPPCU ( 0x110298a, 0x3 )FWLOG: [29837] WHAL_ERROR_RESET_PM ( )Invoking ACS module for Best channel selectionFunction ieee80211_acs_find_best_11na_centerchan best 5G channel is 161OL vap_start +OL vap_start -ol_vdev_start_resp_evol_ath_vap_join: join operation is only for STA/IBSS modeol_ath_wmm_update:Setting vdev param = 3, value = 100Notification to UMAC VAP layereth1: received packet with own address as source addresswmi_unified_vdev_stop_sendSTOPPED EVENT for vap 0Setting vdev param = 1a, value = 1Setting vdev param = 3, value = 100Setting vdev param = d, value = 1Setting vdev param = 12, value = 1Setting vdev param = 1e, value = 1OL vap_stop +wmi_unified_vdev_stop_sendOL vap_stop -STOPPED EVENT for vap 0OL vap_start +OL vap_start -ol_vdev_start_resp_evol_ath_vap_join: join operation is only for STA/IBSS modeol_ath_wmm_update:Setting vdev param = 3, value = 100Notification to UMAC VAP layerdevice ath1 entered promiscuous modebr1: port 3(ath1) entering forwarding state ieee80211_ioctl_siwmode: imr.ifm_active=131738, new mode=3, valid=1wmi_unified_vdev_stop_sendSTOPPED EVENT for vap 0br1: port 3(ath1) entering disabled stateol_ath_vap_set_param: VAP param unsupported param:32 value:0ol_ath_vap_set_param: VAP param unsupported param:121 value:1 DEVICE IS DOWN ifname=ath1 DEVICE IS DOWN ifname=ath1ol_ath_vap_set_param: VAP param unsupported param:32 value:0ol_ath_vap_set_param: VAP param unsupported param:32 value:0ol_ath_vap_set_param: VAP param unsupported param:17 value:1OL vap_stop +wmi_unified_vdev_stop_sendOL vap_stop -STOPPED EVENT for vap 0OL vap_start +OL vap_start -ol_vdev_start_resp_evol_ath_vap_join: join operation is only for STA/IBSS modeol_ath_wmm_update:Setting vdev param = 3, value = 100Notification to UMAC VAP layerbr1: port 3(ath1) entering forwarding stateFWLOG: [36702] WAL_DBGID_BB_WDOG_TRIGGERED ( 0x8f5e, 0x200008a, 0x0, 0x5 )eth1: received packet with own address as source addresswmi_unified_vdev_stop_sendSTOPPED EVENT for vap 0br1: port 3(ath1) entering disabled stateol_ath_vap_set_param: VAP param unsupported param:17 value:1OL vap_stop +wmi_unified_vdev_stop_sendOL vap_stop -STOPPED EVENT for vap 0OL vap_start +OL vap_start -ol_vdev_start_resp_evol_ath_vap_join: join operation is only for STA/IBSS modeol_ath_wmm_update:Setting vdev param = 3, value = 100Notification to UMAC VAP layerbr1: port 3(ath1) entering forwarding statefuse init (API version 7.12)usbcore: registered new interface driver usbfsusbcore: registered new interface driver hubusbcore: registered new device driver usbehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) DriverPort Status 1c000004ath-ehci ath-ehci.0: ATH EHCIath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1ehci_reset Intialize USB CONTROLLER in host mode: 13ehci_reset Port Status 1c000000ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000ehci_reset Intialize USB CONTROLLER in host mode: 13ehci_reset Port Status 1c000000ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00usb usb1: configuration #1 chosen from 1 choicehub 1-0:1.0: USB hub foundhub 1-0:1.0: 1 port detectedPort Status 1c000000ath-ehci1 ath-ehci1.1: ATH EHCIath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2ehci_reset Intialize USB CONTROLLER in host mode: 13ehci_reset Port Status 1c000000ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000ehci_reset Intialize USB CONTROLLER in host mode: 13ehci_reset Port Status 1c000000ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00usb usb2: configuration #1 chosen from 1 choicehub 2-0:1.0: USB hub foundhub 2-0:1.0: 1 port detectedSCSI subsystem initializedInitializing USB Mass Storage driver...usbcore: registered new interface driver usb-storageUSB Mass Storage support registered. GPL NetUSB up!kc 86 : run_telnetDBGDServer startkc 223 : init_DebugD endINFO1758: NetUSB 1.184, 0002061F : May 7 2012 10:35:23INFO175A: AUTH ISOCINFO175B:usbcore: registered new interface driver KC NetUSB General DriverINFO0076: init proc : PAGE_SIZE 4096INFO17B4: Check mac addressINFO162C: infomap 8678c220INFO162F: sleep to wait br0 to wake upINFO02D0: use dev Name br0INFO1638: sleep to wait br0 end.INFO1651: UDP_BROAD 7437 tcpPort:625868800INFO02D0: use dev Name br0INFO1538: tcpConnector() started...INFO1415: Bind to br0

ap135> printenvbootargs=console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),6336k(rootfs),1408k(uImage),64k(mib0),64k(ART)bootcmd=bootm 0x9f020000bootdelay=1baudrate=115200ethaddr=0xba:0xbe:0xfa:0xce:0x08:0x41ipaddr=192.168.1.111serverip=192.168.1.100dir=lu=tftp 0x80060000 ${dir}u-boot.bin&&erase 0x9f000000 +$filesize&&cp.b $fileaddr 0x9f000000 $filesizelf=tftp 0x80060000 ${dir}ap135${bc}-jffs2&&erase 0x9f050000 +0x630000&&cp.b $fileaddr 0x9f050000 $filesizelk=tftp 0x80060000 ${dir}vmlinux${bc}.lzma.uImage&&erase 0x9f680000 +$filesize&&cp.b $fileaddr 0x9f680000 $filesizestdin=serialstdout=serialstderr=serialethact=eth0Environment size: 686/65532 bytes

U-Boot 1.1.4 (Jan 26 2013 - 13:35:40)ap135 - Scorpion 1.0DRAM: sriScorpion 1.0ath_ddr_initial_config(178): (32bit) ddr2 inittap = 0x00000003Tap (low, high) = (0x4, 0x1f)Tap values = (0x11, 0x11, 0x11, 0x11)128 MBFlash Manuf Id 0x1c, DeviceId0 0x30, DeviceId1 0x17flash size 8MB, sector count = 128Flash: 8 MBUsing default environment*** Warning *** : PCIe WLAN Module not found !!!In: serialOut: serialErr: serialNet: ath_gmac_enet_initialize...athrs_sgmii_res_cal: cal value = 0xeNo valid address in Flash. Using fixed addressNo valid address in Flash. Using fixed addressath_gmac_enet_initialize: reset mask:c02200 Scorpion ----> S17 PHY *Vlan config...TEST: FINAL REG VAL after TX Calibration - 0x46000000TEST: FINAL XMII VAL after RX Calibration - 0x56000000TEST: FINAL ETH_CFG VAL after RX Calibration - 0x00028001athrs17_reg_init: complete: cfg1 0x80000000 cfg2 0x7335eth0: ba:be:fa:ce:08:41eth0 upathrs17_reg_init_wan doneSGMII in forced modeathr_gmac_sgmii_setup SGMII done: cfg1 0x800c0000 cfg2 0x7214eth1: ba:be:fa:ce:08:41eth1 upeth0, eth1Setting 0x18116290 to 0x50a1214fAutobooting in 1 seconds## Booting image at 9f020000 ... Uncompressing Kernel Image ... OKStarting kernel ...[ 0.000000] Linux version 3.10.13 (nosferatu@work.g0x.ru) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38284) ) #1 3[ 0.000000] bootconsole [early0] enabled[ 0.000000] CPU revision is: 00019750 (MIPS 74Kc)[ 0.000000] SoC: Qualcomm Atheros QCA9558 rev 0[ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz[ 0.000000] Determined physical RAM map:[ 0.000000] memory: 08000000 @ 00000000 (usable)[ 0.000000] Initrd not found or empty - disabling initrd[ 0.000000] Zone ranges:[ 0.000000] Normal [mem 0x00000000-0x07ffffff][ 0.000000] Movable zone start for each node[ 0.000000] Early memory node ranges[ 0.000000] node 0: [mem 0x00000000-0x07ffffff][ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512[ 0.000000] Kernel command line: board=ARCHER-C7 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)[ 0.000000] Writing ErrCtl register=00000000[ 0.000000] Readback ErrCtl register=00000000[ 0.000000] Memory: 126312k/131072k available (2196k kernel code, 4760k reserved, 588k data, 220k init, 0k highmem)[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1[ 0.000000] NR_IRQS:51[ 0.000000] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)[ 0.060000] pid_max: default: 32768 minimum: 301[ 0.060000] Mount-cache hash table entries: 512[ 0.070000] NET: Registered protocol family 16[ 0.070000] MIPS: machine is TP-LINK Archer C7[ 0.080000] ar724x-pci ar724x-pci.0: PCIe link is down[ 0.080000] registering PCI controller with io_map_base unset[ 0.090000] registering PCI controller with io_map_base unset[ 0.500000] bio: create slab <bio-0> at 0[ 0.500000] PCI host bridge to bus 0000:00[ 0.510000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff][ 0.510000] pci_bus 0000:00: root bus resource [io 0x0000][ 0.520000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff][ 0.520000] PCI host bridge to bus 0000:01[ 0.530000] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff][ 0.530000] pci_bus 0000:01: root bus resource [io 0x0001][ 0.540000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff][ 0.540000] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit][ 0.550000] pci 0000:01:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref][ 0.550000] pci 0000:01:00.0: using irq 41 for pin 1[ 0.560000] Switching to clocksource MIPS[ 0.560000] NET: Registered protocol family 2[ 0.570000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)[ 0.570000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)[ 0.570000] TCP: Hash tables configured (established 1024 bind 1024)[ 0.580000] TCP: reno registered[ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)[ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)[ 0.600000] NET: Registered protocol family 1[ 0.610000] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.[ 0.630000] msgmni has been set to 246[ 0.630000] io scheduler noop registered[ 0.630000] io scheduler deadline registered (default)[ 0.640000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled[ 0.670000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A[ 0.670000] console [ttyS0] enabled, bootconsole disabled[ 0.670000] console [ttyS0] enabled, bootconsole disabled[ 0.690000] ath79-spi ath79-spi: master is unqueued, this is deprecated[ 0.690000] m25p80 spi0.0: found en25q64, expected m25p80[ 0.700000] m25p80 spi0.0: en25q64 (8192 Kbytes)[ 0.700000] 5 tp-link partitions found on MTD device spi0.0[ 0.710000] Creating 5 MTD partitions on "spi0.0":[ 0.710000] 0x000000000000-0x000000020000 : "u-boot"[ 0.720000] 0x000000020000-0x000000118d48 : "kernel"[ 0.730000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- y[ 0.740000] 0x000000118d48-0x0000007f0000 : "rootfs"[ 0.740000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- y[ 0.760000] mtd: partition "rootfs" set to be root filesystem[ 0.760000] 1 squashfs-split partitions found on MTD device rootfs[ 0.770000] 0x000000330000-0x0000007f0000 : "rootfs_data"[ 0.780000] 0x0000007f0000-0x000000800000 : "art"[ 0.780000] 0x000000020000-0x0000007f0000 : "firmware"[ 0.820000] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0[ 2.080000] libphy: ag71xx_mdio: probed[ 2.080000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII[ 2.640000] ag71xx ag71xx.0 eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316][ 2.650000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII[ 3.210000] TCP: cubic registered[ 3.210000] NET: Registered protocol family 17[ 3.220000] 8021q: 802.1Q VLAN Support v1.8[ 3.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.[ 3.230000] Freeing unused kernel memory: 220K (80319000 - 80350000)Console is aliveprocd: Console is alive- watchdog -procd: - watchdog -[ 5.390000] usbcore: registered new interface driver usbfs[ 5.400000] usbcore: registered new interface driver hub[ 5.400000] usbcore: registered new device driver usb[ 5.410000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver[ 5.420000] ehci-platform: EHCI generic platform driver[ 5.420000] ehci-platform ehci-platform.0: EHCI Host Controller[ 5.430000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1[ 5.440000] ehci-platform ehci-platform.0: TX-TX IDP fix enabled[ 5.440000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000[ 5.470000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00[ 5.470000] hub 1-0:1.0: USB hub found[ 5.480000] hub 1-0:1.0: 1 port detected[ 5.480000] ehci-platform ehci-platform.1: EHCI Host Controller[ 5.490000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2[ 5.500000] ehci-platform ehci-platform.1: TX-TX IDP fix enabled[ 5.500000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000[ 5.530000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00[ 5.530000] hub 2-0:1.0: USB hub found[ 5.540000] hub 2-0:1.0: 1 port detectedkmod: ran 19 iterations- preinit -procd: - preinit -Press the [f] key and hit [enter] to enter failsafe mode[ 7.660000] eth0: link up (1000Mbps/Full duplex)mount_root: jffs2 is not ready - marker found[ 8.820000] eth0: link down- early -procd: - early -- watchdog -procd: - watchdog -- init -procd: - init -Please press Enter to activate this console.[ 10.340000] NET: Registered protocol family 10[ 10.350000] nf_conntrack version 0.5.0 (1977 buckets, 7908 max)[ 10.360000] ip6_tables: (C) 2000-2006 Netfilter Core Team[ 10.380000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5[ 10.390000] Backport generated by backports.git backports-20130617-4-ge3220f5[ 10.400000] ip_tables: (C) 2000-2006 Netfilter Core Team[ 10.430000] xt_time: kernel timezone is -0000[ 10.460000] cfg80211: Calling CRDA to update world regulatory domain[ 10.460000] cfg80211: World regulatory domain updated:[ 10.470000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)[ 10.480000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)[ 10.480000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)[ 10.490000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)[ 10.500000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)[ 10.510000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)[ 10.540000] PPP generic driver version 2.4.2[ 10.550000] NET: Registered protocol family 24[ 10.600000] cfg80211: Calling CRDA for country: US[ 10.600000] cfg80211: Regulatory domain changed to country: US[ 10.610000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)[ 10.620000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)[ 10.630000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)[ 10.630000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)[ 10.640000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)[ 10.650000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)[ 10.660000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)[ 10.670000] ieee80211 phy0: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47[ 15.540000] eth1: link up (1000Mbps/Full duplex)[ 15.540000] device eth1 entered promiscuous mode[ 15.570000] br-lan: port 1(eth1) entered forwarding state[ 15.570000] br-lan: port 1(eth1) entered forwarding state[ 15.600000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready[ 15.610000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready[ 16.790000] eth0: link up (1000Mbps/Full duplex)[ 16.810000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready[ 17.570000] br-lan: port 1(eth1) entered forwarding state[ 20.600000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0[ 20.610000] jffs2_build_filesystem(): unlocking the mtd device... done.[ 20.610000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.[ 40.270000] jffs2: notice: (946) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked,.procd: - init complete -BusyBox v1.19.4 (2013-10-02 19:00:12 MSK) built-in shell (ash)Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- BARRIER BREAKER (Bleeding Edge, r38284) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao -----------------------------------------------------root@OpenWrt:/#

• OEM GPL Source (v1): http://www.tp-link.com/resources/gpl/Archer_C7_1.0.tar.gz

• GPL source (v2): http://www.tp-link.com/resources/gpl/ArcherC7v2_un_gpl.zip